DIY Bathtub Installation.
DIY Bathtub Installation.
Blog Article
Are you currently interested in critical info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a bathtub isn't exactly rocket science, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably hard job. If the old tub is easily accessible, the job can move immediately; if you have to open up a wall surface to eliminate the old bathtub and position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need a helper to vacate the old tub and also set in the brand-new one. Make sure you have certified on your own for the task and also are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your tools as well as product checklist need to make up the following:
Preparing for the Installment
To start with, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, put the bathtub in the needed placement. The wooden boards are handy in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the supply of water and inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the maker's user's manual. Tiling and also securing around the bath tub needs to wait until the bath tub has actually been made use of at the very least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type must be linked to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, causing issues with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can crack rather early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give a remark further down. We will be delighted to know your reactions about this posting. Hoping to see you back again in the future. Loved our piece of writing? Please share it. Let another person find it. Thank you for your time invested reading it.
This Post Report this page